Product Details Supplier Info More products

Thomas Birchinger, product manager of draw-wire sensors at Micro-Epsilon, explains how two companies have developed a new approach to measuring the displacement of hydraulic cylinders.

By integrating a draw-wire displacement sensor inside the cylinder, piston rods no longer have to be deep-bore drilled using specialist equipment, irrespective of cylinder stroke length, he said.

Traditionally, there are three different methods of measuring the stroke movements of hydraulic cylinders.

If displacement measurement has already been considered at the design stage, a magnetostrictive sensor can be integrated in the cylinder itself.

Alternatively, if the sensor needs to be fitted to the outside of the cylinder, or retrofitted to the outside of the cylinder, draw-wire sensors, magnetic or optical measuring rods, or tape measures can be used to measure the displacement.

Magnetostrictive sensors are designed so that the measuring element is in a tubular sensor housing.

This is always somewhat longer than the respective measuring range.

The evaluation electronics are located on or at the base of the cylinder at the rear end of the sensor.

For magnetostrictive sensors, a magnet inside the piston is used as the position transmitter.

As these sensors are designed to be pressure proof, they can be integrated in the cylinder.

Modifying the sensor for the application, by adjusting the bar length for example, is usually straightforward.

However, a bore in the piston rod is required for the sensor tube to be immersed in.

The greater the stroke movement of the cylinder, the deeper this bore has to be.

In the case of large-sized cylinders, for example, in sluice gates, this means that a bore size of around 1m may be necessary.

Vertically boring a cylinder piston in this size range and without tilting is a major challenge.

Rather than an integrated displacement measurement, a draw-wire sensor can be mounted on the outside of the cylinder.

This method can be easily achieved, providing measuring ranges of up to a few metres if required.

However, in harsh environments in which cylinders are frequently used, the draw-wire sensor can only be used with caution, since dirt and mechanical loads may destroy the sensor over the long term.

This limitation also applies if optical or magnetic measuring rods are used.

Here, the measuring rod is also installed on the outside of the cylinder.

A grid applied to the bar is scanned optically or inductively.

As this sensor is also outside on the cylinder, it is susceptible to dirt, dust and soiling.

Due to these limitations, two German companies, Sensor-Technik Wiedemann and Micro-Epsilon, have developed an alternative solution.

During the development stage, particular attention was paid to the sensor being suitable for harsh environments and that no significant extra costs would be incurred for integrating the sensor to larger sized cylinders.

This co-developed solution is based on the draw-wire sensor, which is integrated inside the cylinder.

Here, the sensor is completely protected from external influences.

The sensor is positioned at the bottom of the cylinder and the measuring wire is attached to the bottom of the piston.

A particular challenge here was the design of the sensor and the signal routing to the outside, as a bore hole in the cylinder housing is always a weak point.

With pressures of up to 600 bar in the cylinder, leakage is a risk that must be prevented.

As well as the housing, the critical elements of a conventional draw-wire sensor are the spring, the drum, the measuring wire and a protractor used as the sensing element.

A housing for the sensor can be dispensed within this application, as the cylinder takes over this function.

Each movement of the piston causes a rotation of the wire drum.

The rotation movement is divided using a gearbox onto two shafts with different rotational speeds.

A magnet is positioned on each shaft at the bottom of the cylinder, whose positions can be measured by external, magnetic angle sensors.

Using a suitable gearbox, each combination of the magnet positions only occurs once across the complete measuring range.

The sensor therefore shows the characteristics of an absolute encoder.

Micro-Epsilon was able to contribute its expertise in developing the design of the sensor and function of a draw-wire sensor.

Due to the high pressures present, the cylinder walls must be constructed from relatively thick metal.

A magnetic signal transmission through these thick walls is not suitable for measurement requirements.

Due to Sensor-Technik Wiedemann’s experience in pressure measurement technology, a solution was found for this without having to weaken the cylinder design.

At those points where the two gear shafts reach the bottom of the cylinder, the steel is tapered and a special membrane is welded on.

Using this membrane, a magnetic signal can be transmitted with sufficient quality.

Using FEM calculations, the minimum possible wall thickness was determined.

The electronics on the outside were designed to be extremely flat and can easily be attached to the bottom of the cylinder.

The electronics are available with cabling or connector output.

A 4-20mA or a CAN interface are also provided as output options.

Due to the draw-wire sensor, the system can be adapted to different cylinder lengths and diameters and to a diverse range of operating conditions.

Micro-Epsilon’s latest Wiresensor WDS-TZ10 is suitable for cylinders that have a lifting height between 0.5m up to 15m.

The lubricating oil in the cylinder surrounds the draw-wire sensor.

This functions as a lubricator for the sensor, providing a longer service life.

This method is also suitable for cylinders without piston rods due to the hooking of the measuring wire.

Cylinders with this type of displacement measurement are ideally suited to harsh environments and in mobile construction machinery and off-highway vehicles.

For short cylinder strokes, the TZ10 can be used with the magnetostrictive method.

Micro-Epsilon

With over 45 years experience and more than 15,000 customers worldwide, Micro-Epsilon understands the need for accurate, robust, intelligent sensors and measurement systems.

With over 45 years experience and more than 15,000 customers worldwide, Micro-Epsilon understands the need for accurate, robust, intelligent sensors and measurement systems.

If you are measuring any type of displacement / position, temperature, speed or colour parameters, Micro-Epsilon sensors and systems provide market-leading performance, together with the fastest measuring rates, highest operating temperature ranges and smart interface capabilities. From simple, low cost sensors to high volume, customer-specific OEM solutions, Micro-Epsilon will have athe correct measurement solution for your application.

Using both contact and non-contact measurement techniques, Micro-Epsilon boasts one of the largest ranges of displacement sensors including 1D, 2D & 3D laser optical, confocal chromatic, eddy current, capacitive, inductive, draw-wire and time-of-flight technologies. Measuring ranges are from nanometers to kilometers!

For temperature measurement, there is a comprehensive range of non-contact infrared temperature sensors and thermal imaging cameras capable of measuring up to that include intelligent software packages to support configuration, analysis and management during the application. LED analysers, fibre optic sensors and Colour recognition sensors measure true colour using L*A*B and CIE.

Micro-Epsilon sensors are used throughout almost all industries: from automotive to aerospace, motorsport to metal production, semiconductor to subsea. Whether it’s an R&D, test, inspection, OEM or a process control application, Micro Epsilon measurement engineers can provide the right measurement solution.

View full profile