Product Details Supplier Info More products

Precision Spraying Guide

This is a short guide to some common precision spraying techniques that help improve product quality and reduce wastage in a wide variety of industries. Firstly, the guide differentiates the four different types of precision before going on to discuss which spray nozzles need to be deployed to achieve each kind of precision.

What is precision spraying?

Precision in spraying applications comes in four main forms:

Spatial precision

This type of precision is ensuring that the spray only hits the area it needs to. Imprecise spraying will result in fluid being delivered to areas where it is not required. In many cases this will be simply wasteful of product but if, for example, glues are delivered outside the desired area, overspraying can have serious production consequences.

Dosing precision (flow rate)

It is one thing getting the spray on target but also the correct amount of spray needs to be delivered. This means control of the flow rate of spray nozzles needs to be achieved. Variations above or below the desired levels will result in either product defects or wastage.

Consistency precision

Overall flow rates will affect the overall dosing but often thought needs to be given to spray distribution. The evenness of the spray over the area may be a big factor in achieving a good quality product. The spray properties such as average droplet size and variations in spray densities across the spray pattern generated by the nozzle, therefore, need to be understood and controlled for.

Temporal precision

With conveyor spray systems (or with any other systems with relative motion between the spray nozzle and the target) the spatial and dosing precisions mentioned above often translate to temporal precision. Controlling exactly when the nozzle comes on and off will determine where and how much spray is delivered. Having a very crisp and sharp on/off cycle is, therefore, often critical in such systems. Temporal precision is vital in any stop start spraying system.

Methods of control

Fluid pressure

The most basic form of control can be achieved by varying the fluid pressure. This will determine the overall flow rate through the nozzles. A simple pressure regulator will be enough to ensure a consistent flow rate is achieved. Pressure control may be enough for continual runs of product with no on/off spray cycles required.

Air actuated nozzles

If stop start cycles are required as part of a production run, then air actuated spray nozzles will probably be required to achieve the desired level of spatial precision. A hydraulic valve for turning on and off the fluid flow directly will have a lag time before the nozzle is fully turned off and there will be some dripping or poor spraying during this time. Air is far more responsive so an air actuated shut off system can be cycled on and off about 3 times per second. Fluid pressure is continually maintained so the spray is always “ready” to be released. This will normally be responsive enough for most stop start spray applications.

Air control

Air atomising nozzles mix fluid and air to produce fine sprays. The presence of air gives another variable for controlling spray properties. The air mixed with the fluid also helps carry and direct the resulting spray. All this can help with both spatial and consistency control.

The spray properties including spray pattern and droplet size will be determined by both the air and fluid pressure. As there are two variables, a greater degree of control can be achieved over the resulting pattern and consistency of spray. In some air atomising nozzles such as the SAM nozzle, different air feeds are used to control the level of atomisation and the actual spray angle delivered. In such nozzles we now have three independent variables that can be used to control the spray (fluid pressure, atomising air pressure and spray pattern air pressure).

Electrically actuated nozzles

Nozzles within integrated electric valves offer another level of control. These nozzles have a built-in direct shut off system that opens and closes the nozzle orifice up to 150 times per second. Fluid pressure will be maintained. This means that very precise temporal control can be achieved whilst maintaining very good consistency control. Of course, on conveyor systems, good temporal control translates to good spatial control.

A further technique available to electric nozzles also allows for good dosing control. Pulse Width Modulation (PWM) takes advantage of the very rapid on/off cycles available to electric nozzles. By pulsing the nozzle on and off very rapidly the flow rate from the nozzle can be reduced without compromising consistency precision. Normally if a nozzle was pulsed, we would see a degradation in the consistency of any coating produced but with 150Hz pulsing no noticeable effects on consistence can be seen. So, with a 50% on to 50% off very rapid cycle we can reduce the flow rate from the nozzle by 50%.

Pulse Width Modulation

Conveyor speeds

Another way of controlling dosing precision is to vary the speed of conveyors. Slower conveyors will result in a higher dose being delivered and vice versa. Obviously, this control technique is only available to conveyor systems.

Mixed variables

Whilst all the control techniques above have their place, some are less suitable than others. Using fluid pressure to control dosing, for example, will affect spray properties other than just flow rate. So, spray angle and droplet size will also be affected by changes in fluid pressure. This means that for variable product runs that require good spatial and consistency precision, using fluid pressure to control dosing will not be enough.

Similarly, when using air atomising nozzles even through the additional variable of air pressure gives a wider scope of control, all features of the spray will be affected by the air fluid mix. As such, controlling dosing without affecting spray consistency can be difficult. Using external mix air atomisers with independent air feeds for spray shape and atomisation helps solve this greatly. Nevertheless, if we wanted to reduce flow rate whilst keeping everything else consistent some complex calibration experiments would need to be performed. It can be done, but it’s not immediately obvious how changing one parameter will affect the others.

This sometimes-complex interplay between spray variables is not really an issue with standard monolithic production runs. Initial calibrations can be tricky but once the parameters are defined (fluid pressure, air pressure, on/off cycles etc) the production run can be set and left to run. Tweaks to calibration will, hopefully, be fairly few and far between so, even if they are initially tricky, this will not be a big problem in the grand scheme of things.

Variable production runs

When, however, variable production runs are required the complex interactions between spray input variables can be highly problematic. Imagine we have two different product runs both of which require the same consistency of spray and spatial delivery of spray, but one run requires that half the dose is delivered. Varying fluid pressure by a factor of about 4 will change the flow rate by about a factor of 2 but a 4-bar spray will be very different in droplet size to the same fluid at 1 bar.

One solution would be to simply speed up the conveyor for low dose production run. But this might not be possible and, if the high dose schedule is the main product, we are now effectively hobbling production of the main product line for the sake of being able to reduce dosing for a minor product line. It is obvious why conveyor speed techniques are often far from ideal.

Air atomisers with independent air feeds for spray shape and atomisation could be used in such a situation. The initial calibration might be tricky but once the input parameters have been defined for each production run consistent results can be achieved. Fluid and air pressures are simply adjusted for each different production schedule.

An even better solution would be to use the PWM technique discussed above. Electric nozzles can be cycled on and off very rapidly so that a consistent spray can be delivered at different flow rates. As none of the spray input variables change the spatial and consistency precision is maintained. So, with electric nozzles different doses can be programmed; if the highest dose can be achieved by the 100% on spraying schedule while other, lower doses, can be delivered by the same nozzles spraying at the same fluid pressure.

Technique Type of precision Nozzles Required Pro’s Cons
Fluid pressure regulation Dosing / flow rate Any Cheap and simple to implement

Affects other spray properties

Crude

Air actuated shut off Temporal Any fitted with air actuated shut off Simple to implement

Can’t control dosing rate

Air might not be available

Air atomising nozzles

Dosing

Consistency

Spatial

Air Atomising (twin fluid) Nozzles Great variation in spray parameter control particularly with independent air feeds for shape and atomisation

Can be complex to calibrate

Requires air usage which may not be desirable

Higher running cost due to air

Electric shut off

Temporal

Dosing

Electrically actuated nozzles

Very precise temporal control

Simple to change dosing via PWM without affecting other spray parameters

Simple to operate once programs are set up

Expensive to implement

Needs good control system

Conclusions

Precise spraying is important in a wide number of manufacturing processes. There are several advanced spray nozzle products available to achieving desired spraying even across variable production runs. Which techniques are most suitable will vary greatly from situation to situation, but the following universal conclusions can be made:

  • Consider each of the types of control listed above. The most appropriate control techniques can then be selected.
  • Consider the effects of variable runs. The set of nozzles that will only need to cope with one spraying schedule may be different to the nozzles that will need to cope with several different production runs. Some thought up front about this may save a lot of hassle later.
  • Deal with a specialist nozzle manufacturer that you trust. Cheap nozzles made by non-specialist companies will almost certainly have variable spray qualities. This makes precise control almost impossible. Just as important as the product quality though is the expert advice that goes into making correct nozzle selection. A company that really understands spray technology will be able to offer sound and ultimately money-saving advice from the start.

THE SPRAY NOZZLE PEOPLE (SNP)

The Go-to People for spray nozzle solutions

SNP’s aim is to reduce hassle for its customers  when sourcing spray nozzles and systems. The company recognises that components such as spray nozzles probably form only a small part of a client’s project or process. Yet, sourcing the right spray component or solution can be time consuming (and mistakes can prove costly). SNP’s expert sales engineers are skilled in working with customers to get them the best solutions, delivering in-depth technical and application support backed by market-leading products. Typical areas the company advises on include: achieving the optimum drop size for an application, spray coverage flow rates, how different fluids affect spray characteristics and how gas flows will affect spray patterns.

The Go-to People for spray nozzle solutions

SNP’s aim is to reduce hassle for its customers  when sourcing spray nozzles and systems. The company recognises that components such as spray nozzles probably form only a small part of a client’s project or process. Yet, sourcing the right spray component or solution can be time consuming (and mistakes can prove costly). SNP’s expert sales engineers are skilled in working with customers to get them the best solutions, delivering in-depth technical and application support backed by market-leading products. Typical areas the company advises on include: achieving the optimum drop size for an application, spray coverage flow rates, how different fluids affect spray characteristics and how gas flows will affect spray patterns.

SNP supplies spray nozzle solutions to industries worldwide, including the largest engineering, food processing, chemical and petrochemical companies, as well as a vast array of small and medium sized enterprises (SMEs). The company’s product range includes tank washing nozzles, hydraulic nozzles, air atomising nozzles, custom piping assemblies and spray accessories as well as disinfecting and washdown systems.

SNP is as skilled in advising design engineers at the beginning of projects as it is recommending and supplying replacement products that may be needed in a hurry. The company can also provide innovative custom solutions, including using non-standard materials. SNP holds ISO 9001 certification.

SNP is an exclusive distributor for US spray nozzle manufacturer BETE, for  pre-treatment specialist Uni-Spray, specialist paper industry nozzle manufacturer ML Gatewood and tank cleaning systems manufacturer Dasic. In addition, the company suppliers specialist washdown and disinfecting equipment from Lafferty Equipment and Guarany. Orders are handled quickly and efficiently from the company’s dedicated stock-holding facilities.

www.spray-nozzle.co.uk

01273 400092

SNP is part of the Spray People Group (SPG) which supplies a range of specialist products and components to industry. Group companies include the Air Nozzle People (ANP), the Safety Shower People (SSP), the Professional Sprayers People (PSP) and the group’s own fulfilment house The Fulfilment People (TFP).

View full profile