Supplier Network +Add your company

Suppliers A-Z

What you need to know about compressed air desiccant dryers

By Atlas Copco Compressors on

Product Details Supplier Info More products
BD 1100 + installation

Andy Lill, Atlas Copco’s Business Development Manager – Quality Air, outlines the need for dry compressed air, looks at the operation of traditional heatless desiccant dryers, and reveals the benefits of the latest zero-purge desiccant dryer developments.  

Why industry needs really dry air

As any physics student can confirm, air in the atmosphere always contains moisture in the form of water vapour that’s not always welcome. In compressed air, it has the potential to cause problems. The result can be high maintenance costs, shortened service life and impaired air-user performance. Ultimately, untreated air can lead to premature failure of pneumatic equipment. It can also lead to a high rate of end- product rejection, increased leakage, disturbances in instrumentation and control systems, and shorter service life for pipework due to corrosion.

Choosing a reliable desiccant dryer is therefore essential to protect production systems and processes, maintain the quality of end products and minimise energy costs.

Dryer technologies

Regenerative-desiccant-type dryers are the primary choice for compressed air users within the pharmaceutical, chemical, and food and beverage manufacturing industries.

They feature a porous desiccant that adsorbs the moisture by collecting it in its myriad pores, allowing large quantities of water to be retained by a relatively small quantity of desiccant.  The desiccant medium has a finite capacity for adsorbing moisture before it must be dried out or regenerated. Normally, the desiccant is contained in two separate towers. Compressed air to be dried flows through one tower while the desiccant in the other is being regenerated. This is accomplished by reducing the pressure in the tower and passing previously dried purge air through the desiccant bed.

The regeneration air may also be heated, either within the dryer or externally, to reduce the amount of purge air required. Regeneration air may also be supplied by a blower and dryers of this type normally have a regeneration cycle, which can be based upon time, dew point or a combination of the two. The regeneration method depends on the type of desiccant dryer: heatless desiccant dryers or heated blower purge dryers.

BD 850 dryer

Heatless desiccant dryers

Heatless dryers use only compressed air as a purge. Because of their simple design, heatless desiccant dryers are often preferred for extreme environments. This sector includes operations in remote areas, hazardous sites with explosive gases and powders, and applications with a high inlet air temperature.

In the drying process, wet compressed air flows upward through the desiccant which adsorbs the moisture, from the bottom to top of the tower.

During the regeneration cycle, dry air from the outlet of the drying tower is expanded to atmospheric pressure and passed through the saturated desiccant, forcing the adsorbed moisture out.  After desorption, the purge silencer valve is closed, and the vessel is re-pressurised. After regeneration, the functions of both towers are reversed.

Heated blower purge desiccant dryers

Blower purge desiccant dryers use a combination of ambient air from an external blower, heat and a minimal supply of compressed air. In the drying process, wet compressed air flows upward through the desiccant, which adsorbs the moisture, again from bottom to top.

In the regeneration stage, the blower takes ambient air and blows it over an external heater. The heated air is then sent through the saturated desiccant, forcing the adsorbed moisture out.

This stage is followed by a cooling purge: After the heating process is completed, the hot tower of desiccant is cooled by expanding dry compressed air from the outlet of the adsorbing vessel over the hot reactivated tower cooling the desiccant prior to use. As with the heatless process, the function of both towers is then switched automatically.

BD 1100 + detail

Superior energy efficiency

Pressure drop is an important factor in a dryer’s performance. A dryer’s energy consumption is determined by its internal pressure drop and the efficiency of its regeneration process. If a desiccant dryer experiences a high pressure drop, the compressor discharge pressure must be set higher, which increases energy and operating costs. The need for extra pressure requires more energy to produce, and in extreme circumstances may even require a larger output compressor to compensate for an output loss through the dryer, which in some cases can be as much as 20%.

Therefore, it is important to select desiccant dryers that offer a very low pressure drop – below 0.2 bar for most models – as well as the most efficient regeneration process. In recent years, newer dryer technologies with state-of-the-art Elektronikon energy management controls, such as Dewpoint Dependent Switching, have been introduced to fulfil this requirement. The principle is simple. A dewpoint sensor will delay switching towers until the dewpoint falls. This cycle time extension can generate energy savings of up to 90%.

Dryers’ relative life cycle cost – heatless v. heated blower

When calculating lifecycle costs, a heatless desiccant dryer may be considered to be  more expensive to own because it uses a substantial volume of compressed air for purging during regeneration. Typically, average purge air takes up to 16-20% of the rated flow capacity of a heatless dryer.

Despite these losses, the heatless dryer remains a popular choice because of its simplicity and reliability. However, if we compare the total cost of ownership between the two types of dryer over a 10-year lifetime, the heated blower purge type of unit has the advantage over the heatless desiccant method by some 40%.

Although power costs for the heating process would amount to 30% as opposed to zero, this difference is considerably outweighed by the compressed air output losses from the purging operation, which equates to 80% of the TCO.

In terms of other component costs, there are now newer and more advanced dryer technologies, such as the latest models in Atlas Copco’s BD+ range that will guarantee a dew point down to -40°C and are capable of achieving -70°C.  Furthermore, the zero purge losses achieved by the industry-leading BDZP dryers, operating with an inlet flow rate of 300 l/s with a system pressure of 7 Bar G, could see annual savings in the region of £10-14k, based on average kW/hr rates  and when running 24/7 all year round.

Conclusion

The overall conclusion is that for more demanding installations where a negative dew point is required adsorption dryers are regarded as the only valuable solution. But it is a solution that comes with a caveat.

Although the initial purchase price of a heatless desiccant dryer may appear to be attractive, the running costs are extremely high in comparison to other dryer systems. This type of dryer can best be used in applications with a low amount of running hours, or as a back-up unit in a compressed air network to take over in case of issues with the main dryer. On balance, it would appear that dryers featuring heated blower purge with zero purge cooling are the most economical alternative.

Atlas Copco Compressors

Atlas Copco Compressors is a leading manufacturer of energy efficient compressed air systems and vacuum pumps. In the UK the company offers a nationwide sales, service and distribution network and specialist compressed air advice and service to UK compressed air and vacuum users. Our product portfolio covers oil-free air compressors, oil-lubricated air compressors, centrifugal compressors, high-pressure compressors, vacuum pumps, blowers, engineered air and gas compressors, nitrogen generators; air treatment equipment such as dryers, receivers, and air line filters, as well as aluminium pipework for compressed air, nitrogen, oxygen and other gases.

Visit our website 0800 181085

Atlas Copco Compressors is a leading manufacturer of energy efficient compressed air systems and industrial gas generators. In the UK the company has a nationwide sales, service and distribution network to support compressed air and industrial gas users in all industries. Our product portfolio includes oil-free air compressors, oil-lubricated air compressors, air blowers, nitrogen and oxygen generators; air treatment equipment such as dryers, receivers, and filters, as well as pipework. We provide parts and service for any brand of air compressor and we can advise on energy efficiency, system optimisation and connectivity solutions.

View full profile